OpenWRT Page: https://openwrt.org/toh/hwdata/wevo/wevo_11ac_nas
준비물: USB to RS232 TTL
1. OpenWRT 이미지 및 부트로더(u-boot) 이미지 다운로드
Firmware: http://downloads.openwrt.org/releases/18.06.4/targets/ramips/mt7621/openwrt-18.06.4-ramips-mt7621-11acnas-squashfs-sysupgrade.bin
u-boot: https://github.com/pinney/MT7621-u-boot-mod/blob/master/bin/MT7621A_uboot.bin
2. USB to RS232 TTL과 공유기 연결
아래와 같은 설정으로 PuTTY 등으로 시리얼을 연결한다.
Baud rate: 57600, 8-N-1, RTS/CTS
3. PC에 Open TFTP Server 설치
https://sourceforge.net/projects/tftp-server/
C:\OpenTFTPServer 에 OpenWRT와 u-boot 이미지 파일을 넣고 서비스를 실행한다.
4. u-boot 설치
기본 u-boot로 OpenWRT 이미지를 설치하면 무한 리부팅 되므로 첨부된 커스텀 u-boot이미지를 디폴트 u-boot에서 TFTP로 플래싱 한다.
5. Firmware 설치
u-boot에서 TFTP로 OpenWRT 이미지를 플래싱 한다.
6. http://192.168.1.1 로 접속하여 테스트 한다.
U-Boot 1.1.3 (Oct 25 2016 - 10:27:26)
Board: Ralink APSoC DRAM: 448 MB
relocate_code Pointer at: 9bfb4000
Config XHCI 40M PLL
flash manufacture id: c2, device id 20 18
find flash: MX25L12805D
============================================
Pinney UBoot Version: 1.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:Oct 25 2016 Time:10:27:26
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
set LAN/WAN WLL
_ _____ _____
/ / ) / ) ??
/ / / /____/ ___ ___ __
/ / / / / / ) / ) /__) / /
_/____/ ?? /____/ ?? / / / / / / (_ (___/ ??
/
_____/
-------------------------------------------------------------------------
https://github.com/pinney/MT7621-u-boot-mod
-------------------------------------------------------------------------
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
5: Load system code then write to Flash via Httpd.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 4
You chose 2
0
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.0.30) ==:192.168.0.30
Input server IP (192.168.0.152) ==:192.168.0.152
Input Linux Kernel filename ==:f.f.bin
Erasing SPI Flash...
.
Writing to SPI Flash...
.
done
netboot_common, argc= 3
NetTxPacket = 0x9BFE6F80
KSEG1ADDR(NetTxPacket) = 0xBBFE6F80
NetLoop,call eth_halt !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start...
done
Using Eth0 (10/100-M) device
TFTP from server 192.168.0.152; our IP address is 192.168.0.30
Filename 'f.f.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
Got ARP REPLY, set server/gtwy eth addr (58:86:94:f5:de:0f)
Got it
T T #################################################################
#################################################################
#################################################################
#################################################################
##############################################################Got ARP REQUEST, return our IP
###
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#####################################################Got ARP REQUEST, return our IP
############
#################################################################
##############################
done
Bytes transferred = 11797246 (b402fe hex)
NetBootFileXferSize= 00b402fe
....................................................................................................................................................................................
....................................................................................................................................................................................
.
.
Done!
## Booting image at bfc50000 ...
Image Name: 11AC-NAS-Router(0.0.0)
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1875357 Bytes = 1.8 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 448
Starting kernel ...
[ 0.000000] Linux version 4.14.215 (root@otp) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11278-8055e38794)) #0 SMP Tue Jan 19 13:10:02 2021
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is WeVO 11AC NAS Router
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] random: get_random_bytes called from 0x80575744 with crng_init=0
[ 0.000000] percpu: Embedded 14 pages/cpu s26224 r8192 d22928 u57344
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00011848
[ 0.000000] Readback ErrCtl register=00011848
[ 0.000000] Memory: 252464K/262144K available (4751K kernel code, 236K rwdata, 588K rodata, 1260K init, 255K bss, 9680K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 1000MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 3822520893 ns
[ 0.000009] sched_clock: 32 bits at 500MHz, resolution 2ns, wraps every 4294967295ns
[ 0.015508] Calibrating delay loop... 666.41 BogoMIPS (lpj=3332096)
[ 0.087822] pid_max: default: 32768 minimum: 301
[ 0.097128] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110144] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.125784] Hierarchical SRCU implementation.
[ 0.135162] smp: Bringing up secondary CPUs ...
[ 0.145419] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.145427] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.145437] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.145568] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.204589] Synchronize counters for CPU 1: done.
[ 0.274208] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.274216] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.274222] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.274286] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.325209] Synchronize counters for CPU 2: done.
[ 0.386059] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.386066] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.386071] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.386140] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.444773] Synchronize counters for CPU 3: done.
[ 0.504354] smp: Brought up 1 node, 4 CPUs
[ 0.515727] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.535191] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.547614] pinctrl core: initialized pinctrl subsystem
[ 0.559222] NET: Registered protocol family 16
[ 0.573367] pull PCIe RST: RALINK_RSTCTRL = 4000000
[ 0.883449] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.893512] ***** Xtal 40MHz *****
[ 0.900245] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.910448] Port 0 N_FTS = 1b102800
[ 0.917347] Port 1 N_FTS = 1b102800
[ 0.924274] Port 2 N_FTS = 1b102800
[ 2.083283] PCIE2 no card, disable it(RST&CLK)
[ 2.091968] -> 21007f2
[ 2.096790] PCIE0 enabled
[ 2.101989] PCIE1 enabled
[ 2.107169] PCI host bridge /pcie@1e140000 ranges:
[ 2.116693] MEM 0x0000000060000000..0x000000006fffffff
[ 2.127058] IO 0x000000001e160000..0x000000001e16ffff
[ 2.137418] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[ 2.159848] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 2.171103] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 2.182300] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 2.194729] PCI host bridge to bus 0000:00
[ 2.202750] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 2.216426] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 2.228150] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 2.241636] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 2.258042] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.273840] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.290794] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 2.303827] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.317633] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.330768] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.344593] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.358069] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 2.371553] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
[ 2.385888] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 2.399372] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 2.412862] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 2.426325] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.436156] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.449670] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 2.464179] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
[ 2.478508] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.488345] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.501836] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff pref]
[ 2.517373] clocksource: Switched to clocksource GIC
[ 2.528613] NET: Registered protocol family 2
[ 2.537921] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.551671] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.564455] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.577161] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.588666] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.601299] NET: Registered protocol family 1
[ 2.837367] 4 CPUs re-calibrate udelay(lpj = 3325952)
[ 2.848688] Crashlog allocated RAM at address 0x3f00000
[ 2.859165] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 2.877757] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.889238] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.911781] random: fast init done
[ 2.918469] io scheduler noop registered
[ 2.926165] io scheduler deadline registered (default)
[ 2.937553] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 2.953361] console [ttyS0] disabled
[ 2.960413] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 2.978345] console [ttyS0] enabled
[ 2.978345] console [ttyS0] enabled
[ 2.992137] bootconsole [early0] disabled
[ 2.992137] bootconsole [early0] disabled
[ 3.010102] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 3.024384] spi-mt7621 1e000b00.spi: sys_freq: 250000000
[ 3.035833] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 3.045967] 4 fixed-partitions partitions found on MTD device spi0.0
[ 3.058624] Creating 4 MTD partitions on "spi0.0":
[ 3.068167] 0x000000000000-0x000000030000 : "u-boot"
[ 3.078998] 0x000000030000-0x000000040000 : "u-boot-env"
[ 3.090489] 0x000000040000-0x000000050000 : "factory"
[ 3.101447] 0x000000050000-0x000001000000 : "firmware"
[ 3.112766] 2 uimage-fw partitions found on MTD device firmware
[ 3.124592] Creating 2 MTD partitions on "firmware":
[ 3.134507] 0x000000000000-0x0000001c9ddd : "kernel"
[ 3.145335] 0x0000001c9ddd-0x000000fb0000 : "rootfs"
[ 3.156126] mtd: device 5 (rootfs) set to be root filesystem
[ 3.167530] 1 squashfs-split partitions found on MTD device rootfs
[ 3.179843] 0x000000b10000-0x000000fb0000 : "rootfs_data"
[ 3.192117] libphy: Fixed MDIO Bus: probed
[ 3.269371] libphy: mdio: probed
[ 4.675432] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[ 4.687960] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 4.707017] NET: Registered protocol family 10
[ 4.717307] Segment Routing with IPv6
[ 4.724741] NET: Registered protocol family 17
[ 4.733662] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 4.759450] 8021q: 802.1Q VLAN Support v1.8
[ 4.770012] hctosys: unable to open rtc device (rtc0)
[ 4.785919] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 4.804268] Freeing unused kernel memory: 1260K
[ 4.813331] This architecture does not have kernel memory protection.
[ 5.649745] init: Console is alive
[ 5.656733] init: - watchdog -
[ 6.408952] mtk_soc_eth 1e100000.ethernet eth0: port 2 link up
[ 7.533804] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 7.610472] usbcore: registered new interface driver usbfs
[ 7.621538] usbcore: registered new interface driver hub
[ 7.632230] usbcore: registered new device driver usb
[ 7.649878] SCSI subsystem initialized
[ 7.665164] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
[ 7.682488] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[ 7.700164] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 7.710798] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 7.737527] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
[ 7.755817] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 7.768247] hub 1-0:1.0: USB hub found
[ 7.775776] hub 1-0:1.0: 2 ports detected
[ 7.784360] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 7.794997] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 7.809914] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 7.822909] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 7.839813] hub 2-0:1.0: USB hub found
[ 7.847396] hub 2-0:1.0: 1 port detected
[ 7.862315] usbcore: registered new interface driver usb-storage
[ 7.875986] usbcore: registered new interface driver uas
[ 7.887036] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.917694] init: - preinit -
[ 9.051859] mtk_soc_eth 1e100000.ethernet: PPE started
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 12.219983] mount_root: loading kmods from internal overlay
[ 12.266297] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 12.280923] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 12.642360] block: attempting to load /etc/config/fstab
[ 12.654083] block: unable to load configuration (fstab: Entry not found)
[ 12.667550] block: no usable configuration
[ 12.676468] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 12.724500] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 12.791757] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[ 12.813034] procd: - early -
[ 12.818913] procd: - watchdog -
[ 13.557535] procd: - watchdog -
[ 13.564080] procd: - ubus -
[ 13.713110] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.748146] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.761290] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.774748] procd: - init -
Please press Enter to activate this console.
[ 14.369733] kmodloader: loading kernel modules from /etc/modules.d/*
[ 14.389356] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 14.401856] tun: Universal TUN/TAP device driver, 1.6
[ 14.421082] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.438322] Netfilter messages via NETLINK v0.30.
[ 14.450769] ip_set: protocol 6
[ 14.485177] Mirror/redirect action on
[ 14.501203] u32 classifier
[ 14.506598] input device check on
[ 14.513891] Actions configured
[ 14.535483] urngd: v1.0.2 started.
[ 14.535700] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[ 14.563196] fuse init (API version 7.26)
[ 14.580124] Loading modules backported from Linux version v4.19.161-0-gdaefdc9eb24b
[ 14.595434] Backport generated by backports.git v4.19.161-1-0-g4bb568fe
[ 14.611430] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.687956] nf_conntrack_rtsp v0.7 loading
[ 14.718494] random: crng init done
[ 14.725322] random: 7 urandom warning(s) missed due to ratelimiting
[ 14.782488] nf_nat_rtsp v0.7 loading
[ 14.803259] nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net>
[ 14.853201] usbcore: registered new interface driver ums-alauda
[ 14.866702] usbcore: registered new interface driver ums-cypress
[ 14.881108] usbcore: registered new interface driver ums-datafab
[ 14.895135] usbcore: registered new interface driver ums-freecom
[ 14.909170] usbcore: registered new interface driver ums-isd200
[ 14.923383] usbcore: registered new interface driver ums-jumpshot
[ 14.937979] usbcore: registered new interface driver ums-karma
[ 14.952062] usbcore: registered new interface driver ums-sddr09
[ 14.965767] usbcore: registered new interface driver ums-sddr55
[ 14.979701] usbcore: registered new interface driver ums-usbat
[ 15.029590] xt_time: kernel timezone is -0000
[ 15.128000] usbcore: registered new interface driver mt7601u
[ 15.142571] bus=0x1, slot = 0x0, irq=0xff
[ 15.150618] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
[ 15.162252] mt7603e 0000:01:00.0: ASIC revision: 76030010
[ 16.200718] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
[ 16.211903] mt7603e 0000:01:00.0: Build Time: 20160107100755
[ 16.257361] mt7603e 0000:01:00.0: firmware init done
[ 16.451708] bus=0x2, slot = 0x1, irq=0xff
[ 16.459746] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
[ 16.471266] mt76x2e 0000:02:00.0: ASIC revision: 76120044
[ 17.192320] mt76x2e 0000:02:00.0: ROM patch build: 20141115060606a
[ 17.207870] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00
[ 17.218813] mt76x2e 0000:02:00.0: Build: 1
[ 17.226948] mt76x2e 0000:02:00.0: Build Time: 201507311614____
[ 17.257364] mt76x2e 0000:02:00.0: Firmware running!
[ 17.274999] usbcore: registered new interface driver mt76x2u
[ 17.301628] PPP generic driver version 2.4.2
[ 17.312012] NET: Registered protocol family 24
[ 17.329243] batman_adv: B.A.T.M.A.N. advanced openwrt-2019.2-10 (compatibility version 15) loaded
[ 17.355182] usbcore: registered new interface driver mt76x0u
[ 17.369652] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 33.244037] mtk_soc_eth 1e100000.ethernet: PPE started
[ 33.261079] br-lan: port 1(eth0.1) entered blocking state
[ 33.271895] br-lan: port 1(eth0.1) entered disabled state
[ 33.283756] device eth0.1 entered promiscuous mode
[ 33.293337] device eth0 entered promiscuous mode
[ 33.306368] br-lan: port 1(eth0.1) entered blocking state
[ 33.317216] br-lan: port 1(eth0.1) entered forwarding state
[ 33.328833] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 34.308229] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 38.414227] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 38.428003] jffs2_build_filesystem(): unlocking the mtd device...
[ 38.428014] done.
[ 38.444437] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 60.794728] done.
[ 60.813476] jffs2: notice: (2872) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 61.316671] overlayfs: upper fs does not support tmpfile.
BusyBox v1.30.1 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
WeVO 11AC NAS 19.07.6, r11278-8055e38794
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#
